CVE-2014-3018
Official description Straight from the sourceThe vendor's or NVD's own wording, published unedited. Authoritative, but often terse — it says what broke, rarely what to do.
NVD · uneditedIBM BladeCenter SAS Connectivity Module (aka NSSM) and SAS RAID Module (aka RSSM) before 1.3.3.006 allow remote attackers to cause a denial of service (reboot) via a flood of IP packets.
Technical summary Written by usOur analysis, written from the advisory, the CVSS vector and the affected-version data. It adds context the advisory leaves out, and never invents facts that are not in the source.
dbcve analysis · high confidenceIBM BladeCenter SAS Connectivity Module (NSSM) and SAS RAID Module (RSSM) before version 1.3.3.006 are vulnerable to remote denial of service attacks. Attackers can cause forced reboots by flooding the devices with IP packets, likely due to insufficient handling of high-volume network traffic.
Verify against the referenced sources before acting — the references below are authoritative for this CVE, this summary is not.
Affected products & versions What the vendor confirmedThe version ranges the vendor confirmed as vulnerable. If your version sits inside a range here, treat yourself as exposed until you have upgraded.
NVD · CPE data<= 1.3.3.004<= 1.3.3.004CVSS breakdown How the score is builtThe industry scoring standard. It rates how the flaw is reached, what it takes to exploit, and what an attacker gains — the score is derived from those, not the other way round.
From the vector- Attack vector
- Network
- Complexity
- Low
- Authentication
- None
- Confidentiality
- None
- Integrity
- None
- Availability
- Complete
AV:N/AC:L/Au:N/C:N/I:N/A:C
Am I affected? How to checkSteps we derive from the advisory and the affected-version data, so you can decide whether this CVE reaches your setup. They are a guide, not a scan — your own configuration is the authority.
dbcve checksWork through these to decide whether this CVE applies to you.
-
Identify the module typeLocate the IBM BladeCenter module in your inventory - determine whether it is a SAS Connectivity Module (NSSM) or SAS RAID Module (RSSM). This information is typically available in the BladeCenter management interface or hardware inventory.Affected if The module is either an NSSM or RSSM and the firmware version is 1.3.3.004 or earlier
-
Check the installed firmware versionAccess the BladeCenter management interface (either the Advanced Management Module web GUI or CLI) and navigate to the module information page for the SAS Connectivity Module or SAS RAID Module to view the current firmware version.Affected if The displayed firmware version is 1.3.3.004 or any version lower than 1.3.3.006
-
Verify network accessibility of the management interfaceDetermine whether the management network port for the affected module is exposed to untrusted networks. Check the network segment where the BladeCenter management IP is reachable, and review any firewall rules or ACLs controlling access to the module management ports.Affected if The module management interface is reachable from network segments that contain untrusted or internet-facing systems
-
Confirm the vulnerability trigger conditionReview any existing network logs or monitoring data for signs of high-volume traffic directed at the module IP address that could indicate a packet flood condition leading to unexpected reboots.Affected if The module has experienced or is susceptible to forced reboots correlating with periods of high network traffic to the module
You are affected if your environment contains an IBM SAS Connectivity Module (NSSM) or SAS RAID Module (RSSM) running firmware version 1.3.3.004 or earlier, and the module management interface is network-accessible to potential attackers.
Generated from the published advisory. Verify against your own configuration.
Remediation Closing itWhat it takes to close this. Where a vendor fix exists we point at it; where none exists we say so plainly, and can build one. Effort estimates are scoped from the advisory, not from your codebase.
From vendor dataUpgrade the affected modules to firmware version 1.3.3.006 or later to remediate this vulnerability. Consider implementing network-level traffic filtering or rate limiting as an additional safeguard.
- Consultation3.0 h
- Implementation6.0 h
- Testing3.0 h
- Review / QA2.0 h
An estimate, not a bill — we confirm scope with you before any work starts. Need it this week? Rush from $3,984.
Scan for this in your stack
Free · runs locallyCheck whether your project pulls in CVE-2014-3018 — or any other known-vulnerable package — straight from your lock files. Free and open source; it runs locally and uploads nothing.
References Go to the primary sourcePrimary sources — vendor advisories, patches and trackers. Where our summary and a reference disagree, the reference wins.
Primary sourcesPractitioner notes
ContributedPeer-ranked notes from engineers who’ve handled CVE-2014-3018 in production — separate from our analysis above.
The advisory tells you what broke. It rarely tells you what actually worked. If you’ve dealt with this one, that detail is what the next engineer is searching for.
- The version that genuinely resolved it — not the one the vendor claimed
- A config change or rule that shut the vector down
- A gotcha in the upgrade path that cost you an afternoon
No notes yet
Be the first to add a field note for this CVE — a mitigation you’ve verified, a version caveat, or a link to a working fix. Sign in above to contribute.
A place for practitioners to share what actually worked: a mitigation you’ve tested, a configuration change, a version- or environment-specific caveat, or a link to a verified patch. The most useful notes rise to the top as peers upvote them, so the signal stays high.
- Verified mitigations, workarounds, and config changes
- Version or environment caveats, and links to real fixes
- No weaponised exploit code, or anything meant to cause harm
- No spam, self-promotion, credentials, or personal data