Ie Sw Pl09m 5gc 4gt FirmwareOperating system · Weidmueller

CVE-2019-16672

CRITICAL · 9.8 CVSS v3.1 Published 2019-12-06
Fix available
A fix is available. Upgrade to after 3.4.4 or later.
See remediation →
100/100
Remediation priority · Urgent
Remotely reachable No privileges Zero-click

Official description Straight from the sourceThe vendor's or NVD's own wording, published unedited. Authoritative, but often terse — it says what broke, rarely what to do.

NVD · unedited
An issue was discovered on Weidmueller IE-SW-VL05M 3.6.6 Build 16102415, IE-SW-VL08MT 3.5.2 Build 16102415, and IE-SW-PL10M 3.3.16 Build 16102416 devices. Sensitive Credentials data is transmitted in cleartext.

Technical summary Written by usOur analysis, written from the advisory, the CVSS vector and the affected-version data. It adds context the advisory leaves out, and never invents facts that are not in the source.

dbcve analysis · moderate confidence

The Weidmueller industrial ethernet switches (IE-SW-VL05M, IE-SW-VL08MT, and IE-SW-PL10M) transmit sensitive credentials such as usernames and passwords in cleartext without encryption, allowing network interceptors to capture authentication credentials in plain text.

MitigationEnable encrypted communication protocols (HTTPS, SSH, VPN tunnel) for all management access to prevent credential interception; verify if firmware updates are available from Weidmueller to address this vulnerability.

Verify against the referenced sources before acting — the references below are authoritative for this CVE, this summary is not.

Affected products & versions What the vendor confirmedThe version ranges the vendor confirmed as vulnerable. If your version sits inside a range here, treat yourself as exposed until you have upgraded.

NVD · CPE data
Ie Sw Pl09m 5gc 4gt FirmwareOperating system
Affected:<= 3.3.4
Ie Sw Pl09mt 5gc 4gt FirmwareOperating system
Affected:<= 3.3.4
Ie Sw Pl18m 2gc 16tx FirmwareOperating system
Affected:<= 3.4.4
Ie Sw Pl18mt 2gc 16tx FirmwareOperating system
Affected:<= 3.4.4
Ie Sw Pl18m 2gc14tx2sc FirmwareOperating system
Affected:<= 3.4.4
Ie Sw Pl18mt 2gc14tx2sc FirmwareOperating system
Affected:<= 3.4.4
Ie Sw Pl18m 2gc14tx2st FirmwareOperating system
Affected:<= 3.4.4
Ie Sw Pl18mt 2gc14tx2st FirmwareOperating system
Affected:<= 3.4.4

CVSS breakdown How the score is builtThe industry scoring standard. It rates how the flaw is reached, what it takes to exploit, and what an attacker gains — the score is derived from those, not the other way round.

From the vector
Attack vector
Network
Complexity
Low
Privileges
None
User interaction
None
Scope
Unchanged
Confidentiality
High
Integrity
High
Availability
High

CVSS:3.1/AV:N/AC:L/PR:N/UI:N/S:U/C:H/I:H/A:H

Am I affected? How to checkSteps we derive from the advisory and the affected-version data, so you can decide whether this CVE reaches your setup. They are a guide, not a scan — your own configuration is the authority.

dbcve checks

Work through these to decide whether this CVE applies to you.

  1. Identify the Weidmueller switch model
    Access the device web interface or console and locate the model number (e.g., IE-SW-PL09M, IE-SW-PL18M) displayed in the system information or device status page
    Affected if The model is one of the affected variants: IE-SW-VL05M, IE-SW-VL08MT, IE-SW-PL10M, IE-SW-PL09M, IE-SW-PL09MT, IE-SW-PL18M, IE-SW-PL18MT, or related 2gc/2sc/2st variants
  2. Check the installed firmware version
    In the device web interface, navigate to System > Firmware or System > Information to view the firmware version; alternatively, use the CLI command 'show version' or 'system info' via console/SSH
    Affected if The firmware version is 3.3.4 or lower for PL09M/PL09MT models, or 3.4.4 or lower for PL18M/PL18MT models and related variants
  3. Verify if HTTP (cleartext) is enabled for management
    In the web interface, go to System > Network Settings or Security > Access and check whether HTTP (port 80) is enabled for web management; also check if HTTPS (port 443) is the only allowed protocol
    Affected if HTTP is enabled and accessible for web-based management login, allowing credentials to be transmitted in cleartext over the network
  4. Capture network traffic during login to confirm cleartext transmission
    Use a network packet capture tool (e.g., Wireshark) on the management network segment and observe the traffic when logging into the device web interface; look for HTTP POST or login packets containing plaintext username and password fields
    Affected if Login credentials are observable in plain text within captured network packets, indicating the vulnerability is exploitable in the current configuration

The environment is affected if a Weidmueller switch model from the affected list is running firmware at or below the specified version limits AND HTTP management access is enabled, allowing credentials to be intercepted in cleartext.

Generated from the published advisory. Verify against your own configuration.

Check your environment

Paste your version and any relevant configuration and it will be compared against the affected criteria above. Do not include secrets or credentials.

AI-assisted, checked against the advisory. Informational, not a guarantee.

Remediation Closing itWhat it takes to close this. Where a vendor fix exists we point at it; where none exists we say so plainly, and can build one. Effort estimates are scoped from the advisory, not from your codebase.

From vendor data
Upgrade available Upgrade to a release after 3.4.4
Interim mitigation

Enable encrypted communication protocols (HTTPS, SSH, VPN tunnel) for all management access to prevent credential interception; verify if firmware updates are available from Weidmueller to address this vulnerability.

Fix this in Ie Sw Pl09m 5gc 4gt Firmware Scoped from the published advisory
  • Consultation4.0 h
  • Implementation8.0 h
  • Testing4.0 h
  • Review / QA2.0 h
18.0 hours of engineering $3,200
Get the upgrade done

An estimate, not a bill — we confirm scope with you before any work starts. Need it this week? Rush from $5,120.

Scan for this in your stack

Free · runs locally
dbcve dependency scanner

Check whether your project pulls in CVE-2019-16672 — or any other known-vulnerable package — straight from your lock files. Free and open source; it runs locally and uploads nothing.

References Go to the primary sourcePrimary sources — vendor advisories, patches and trackers. Where our summary and a reference disagree, the reference wins.

Primary sources

Practitioner notes

Contributed

Peer-ranked notes from engineers who’ve handled CVE-2019-16672 in production — separate from our analysis above.

No notes yet

Be the first to add a field note for this CVE — a mitigation you’ve verified, a version caveat, or a link to a working fix. Sign in above to contribute.

What this is

A place for practitioners to share what actually worked: a mitigation you’ve tested, a configuration change, a version- or environment-specific caveat, or a link to a verified patch. The most useful notes rise to the top as peers upvote them, so the signal stays high.

What belongs here
  • Verified mitigations, workarounds, and config changes
  • Version or environment caveats, and links to real fixes
  • No weaponised exploit code, or anything meant to cause harm
  • No spam, self-promotion, credentials, or personal data