Wap125 FirmwareOperating system · Cisco

CVE-2021-1547

HIGH · 7.2 CVSS v3.1 Published 2021-05-22
Fix available
A fix is available. Upgrade to after 1.1.2.4 or later.
See remediation →
78/100
Remediation priority · High
Remotely reachable Zero-click

Official description Straight from the sourceThe vendor's or NVD's own wording, published unedited. Authoritative, but often terse — it says what broke, rarely what to do.

NVD · unedited
Multiple vulnerabilities in the web-based management interface of certain Cisco Small Business 100, 300, and 500 Series Wireless Access Points could allow an authenticated, remote attacker to perform command injection attacks against an affected device. These vulnerabilities are due to improper validation of user-supplied input. An attacker could exploit these vulnerabilities by sending crafted HTTP requests to the web-based management interface of an affected system. A successful exploit could allow the attacker to execute arbitrary commands with root privileges on the device. To exploit these vulnerabilities, the attacker must have valid administrative credentials for the device.

Technical summary Written by usOur analysis, written from the advisory, the CVSS vector and the affected-version data. It adds context the advisory leaves out, and never invents facts that are not in the source.

dbcve analysis · high confidence

This CVE describes command injection vulnerabilities in the web-based management interface of Cisco Small Business 100, 300, and 500 Series Wireless Access Points. The vulnerabilities stem from improper validation of user-supplied input in HTTP requests, allowing authenticated attackers to inject and execute arbitrary commands with root privileges on the affected device.

MitigationApply the vendor-supplied firmware patch from Cisco. If patches are unavailable, restrict web management interface access to trusted administrative networks only and ensure strong credential policies.

Verify against the referenced sources before acting — the references below are authoritative for this CVE, this summary is not.

Affected products & versions What the vendor confirmedThe version ranges the vendor confirmed as vulnerable. If your version sits inside a range here, treat yourself as exposed until you have upgraded.

NVD · CPE data
Wap125 FirmwareOperating system
Affected:<= 1.0.3.1
Wap131 FirmwareOperating system
Affected:<= 1.0.2.17
Wap150 FirmwareOperating system
Affected:<= 1.1.2.4
Wap351 FirmwareOperating system
Affected:<= 1.0.2.17
Wap361 FirmwareOperating system
Affected:<= 1.1.2.4
Wap581 FirmwareOperating system
Affected:<= 1.0.3.1

CVSS breakdown How the score is builtThe industry scoring standard. It rates how the flaw is reached, what it takes to exploit, and what an attacker gains — the score is derived from those, not the other way round.

From the vector
Attack vector
Network
Complexity
Low
Privileges
High
User interaction
None
Scope
Unchanged
Confidentiality
High
Integrity
High
Availability
High

CVSS:3.1/AV:N/AC:L/PR:H/UI:N/S:U/C:H/I:H/A:H

Am I affected? How to checkSteps we derive from the advisory and the affected-version data, so you can decide whether this CVE reaches your setup. They are a guide, not a scan — your own configuration is the authority.

dbcve checks

Work through these to decide whether this CVE applies to you.

  1. Identify the wireless access point model
    Log into the device web interface or check the device label to determine the exact model number (WAP125, WAP131, WAP150, WAP351, WAP361, or WAP581)
    Affected if The model is one of these six series devices
  2. Check the installed firmware version
    Access the device web management interface, typically at the device IP address, and navigate to the Status or Administration section to view the firmware version. Alternatively, check the device documentation for CLI access and use 'show version' or similar command.
    Affected if The firmware version is at or below 1.0.3.1 for WAP125/WAP581, 1.0.2.17 for WAP131/WAP351, or 1.1.2.4 for WAP150/WAP361
  3. Verify the web-based management interface is enabled
    In the device web interface, navigate to the Administration or Management settings and confirm whether the HTTP/HTTPS web management interface is turned on.
    Affected if The web-based management interface is enabled and accessible
  4. Determine network exposure of the management interface
    Check the device network configuration to see if the web management interface is bound to all interfaces (0.0.0.0) or only specific IP addresses. Review firewall or ACL rules that may allow access to the management web port from untrusted networks.
    Affected if The web management interface is reachable from untrusted or external networks rather than only from a trusted administrative subnet

The device is affected if it is a WAP125, WAP131, WAP150, WAP351, WAP361, or WAP581 running firmware at or below the versions specified, and the web-based management interface is enabled and accessible.

Generated from the published advisory. Verify against your own configuration.

Check your environment

Paste your version and any relevant configuration and it will be compared against the affected criteria above. Do not include secrets or credentials.

AI-assisted, checked against the advisory. Informational, not a guarantee.

Remediation Closing itWhat it takes to close this. Where a vendor fix exists we point at it; where none exists we say so plainly, and can build one. Effort estimates are scoped from the advisory, not from your codebase.

From vendor data
Upgrade available Upgrade to a release after 1.1.2.4
Interim mitigation

Apply the vendor-supplied firmware patch from Cisco. If patches are unavailable, restrict web management interface access to trusted administrative networks only and ensure strong credential policies.

Fix this in Wap125 Firmware Scoped from the published advisory
  • Consultation4.0 h
  • Implementation8.0 h
  • Testing6.0 h
  • Review / QA4.0 h
22.0 hours of engineering $3,860
Get the upgrade done

An estimate, not a bill — we confirm scope with you before any work starts. Need it this week? Rush from $6,176.

Scan for this in your stack

Free · runs locally
dbcve dependency scanner

Check whether your project pulls in CVE-2021-1547 — or any other known-vulnerable package — straight from your lock files. Free and open source; it runs locally and uploads nothing.

References Go to the primary sourcePrimary sources — vendor advisories, patches and trackers. Where our summary and a reference disagree, the reference wins.

Primary sources

Practitioner notes

Contributed

Peer-ranked notes from engineers who’ve handled CVE-2021-1547 in production — separate from our analysis above.

No notes yet

Be the first to add a field note for this CVE — a mitigation you’ve verified, a version caveat, or a link to a working fix. Sign in above to contribute.

What this is

A place for practitioners to share what actually worked: a mitigation you’ve tested, a configuration change, a version- or environment-specific caveat, or a link to a verified patch. The most useful notes rise to the top as peers upvote them, so the signal stays high.

What belongs here
  • Verified mitigations, workarounds, and config changes
  • Version or environment caveats, and links to real fixes
  • No weaponised exploit code, or anything meant to cause harm
  • No spam, self-promotion, credentials, or personal data